2016年7月14日星期四

Installation Of Grinding Wheel(一)

Grinding wheel: Central abrasive and a binder resin made of a circular abrasive through hole. Abrasive wheel is the most widely used as a maximum amount, the use of face, high-speed rotation, can the outer, inner circle, plane type and various other metal or non-metal surface of the workpiece when using coarse grinding, fine grinding and half grooving and grinding and cutting and so on.

Grinding wheel is the most important for a class of abrasive. Abrasive wheel is added to the binding agent, a porous body through compacts made of dried and calcined. Due to the abrasive, bond and different manufacturing processes, a large difference in characteristics of the wheel, so the grinding process quality, productivity and economy have an important impact. The characteristics of the wheel mainly determined by the abrasive particle size, binder, hardness, structure, shape and size and other factors.
1 classificationWheel variety.
The press can be divided into ordinary abrasive abrasive (corundum and silicon carbide) abrasive grinding wheel and the natural and super abrasive (diamond and cubic boron nitride) grinding wheel;According to the shape can be divided into flat-shaped grinding wheel, bevel wheel, cylindrical grinding wheel, cup wheel, disc wheel and so on; press binding agent can be divided into ceramic wheel, resin wheel, rubber wheel, metal grinding wheel. The main parameters of the abrasive wheel, viscosity, hardness, binding agents, shape, size and so on.
Since the wheel typically operate at high speed, before turning test should be carried out so that the use of (guaranteed wheel at the maximum operating speed, do not break) and static balance test (when working to prevent vibrations caused by the machine). Grindstone at work for some time, it should be trimmed in order to restore the grinding performance and the correct geometry.
2, propertyAbrasive wheel is the central and the binding agent made of a circular abrasive through hole

2016年7月12日星期二

Grinding wheel is the most important for a class of abrasive. Abrasive wheel is added to the binding agent, a porous body through compacts made of dried and calcined. Due to the abrasive, bond and different manufacturing processes, a large difference in characteristics of the wheel, so the grinding process quality, productivity and economy have an important impact.
Summary:
Also known as abrasive grinding wheel, grinding wheel by ordinary abrasive binder consolidated into a certain shape (mostly circular, the central through-hole), and has a certain strength of abrasive. Which generally consists of abrasive, binder and pore structure, these three parts is often called bonded abrasives three elements. According to different classification binding agent, a common ceramic (binder) wheel, resin (binder) wheel, rubber (binder) wheel. Abrasive wheel is the most widely used as a maximum amount, the use of face, high-speed rotation, can the outer, inner circle, plane type and various other metal or non-metal surface of the workpiece when using coarse grinding, fine grinding and half grooving and grinding and cutting and so on.

2016年7月11日星期一

In fact, all
Grinding wheel
Divided into soft, soft, hard, hard few. Each is divided into several levels. English by
Soft to hard into
: E,F,G,H,I,J,K,L,M,N,O,P,Q,R
And other. Hard sand wheel Abrasive
Not falling,
Metal shavings mill under easy to stick on the wheel,
Cause surface burns;
Soft abrasive grinding wheel
Easy to fall off, do not burn the workpiece, the grinding wheel consumed faster.



      
We speak of soft wheel, the wheel does not mean that such a soft crystal particles, but rather a strong combination of sand
Of soft,
Easier to fall off,
So that when the sand is ground a little too sharp not to fall off,
Under its new sharp sand
Continue grinding grain, which has been maintained
Abrasive
Sharp, and then a hard material is also a softness
.



  

   
If we use the head-on approach, there will be two-meet, each side of the situation, and the wheel material
Serious slippage occurs between the materials,
No one who approaches,
On the ground does not move.
Soft wheel applies to the amount of feed
Big
/
Large contact surface
/
Hard material
/
Poor heat resistance grinding
.
Hard wheel suitable for feed less
/
Soft material
/
Small ground contact surface of each grinding or narrow field
.



      
Wheel hardness choose the right time,
Grinding process to blunt the abrasive off on their own,
Exposing new sharp
Continue abrasive grinding.
If the selected wheel is too soft,
Not abrasive passivation off prematurely,
Not only increased consumption of the grinding wheel,
But also lose the right wheel shape and machining accuracy;
If the selected wheel too hard,
After the abrasive grains can not be passive and
When off,
Make abrasive grinding wheel surface voids between the debris is blocked,
Resulting in increased grinding force,
Grinding heat gain
More grinding temperature, so that the workpiece deformation even burn, and the surface roughness to improve productivity
decline.





      
Soft material with a hard grinding wheel reason it will not need to go into detail, soft material with a soft grinding wheel is not no,
Is too wasted effort,
Soft material and hard material is greater than the coefficient of friction, the soft sand on the surface of the wheel to fall off more easily,
sand
When grain is also sharp and lost,
No full capacity,
Wheel soon rebuilt,
There may even be more than the wheel
Wear soft material faster situation,
Or grinding does not move appears the phenomenon,
Then the grinding efficiency is greatly reduced,
and so
Then you should use a combination of strong hard wheel. Knowledge binding agent
,
Other articles repeat
.


Generally, when grinding hard materials, grinding wheel hardness should be lower; on the contrary, it should be higher. Non-ferrous metal toughness
Big wheel pore clogging debris easily, generally should not be grinding. To grind, you should choose a softer wheel. Correct
To form grinding and precision grinding,
In order to maintain a good shape accuracy of the grinding wheel,
You should choose harder wheel.
one
Grinding is often used as soft to medium-hard grade level wheel.

The technical hinder of easy decyclization of Ultra Dished No.3 Grinding-wheels was solved

The wheels are specially made for all kinds of jig grinder, tool grinder and complicated cutters. They are mainly used for the processing of all specifications of high-speed steel, hard-alloy rotary file, technical drill, and dentistry drill, milling cutter, stones and ceramic products. Wheel of every size and specification can be manufactured based on the actual condition of equipments and detailed requirements of clients.
Grinding-wheels are manufactured into different models and patterns according to specfic grindings and grinders. Ordinary Grinding-wheels include: Plain Grinding-wheel, Tubbish Grinding-wheel, Cup Grinding-wheel, Dished Grinding-wheel and Taper-cup Grinding-wheel etc.
We manufacture Diamond/CBN Grinding-wheels and abrasive-materials; Adopt of field of Glass and ceramic grinding; Metallic Grinding-wheels and Resinoid Grinding-wheels used in Glass-processing field; Polishing wheel; Diamond tools used to process magnetic and hard-alloy materials; in addition to irregular Diamond/CBN Grinding-wheels suit to different grinding.
Dished Grinding-wheel No.3 was developed under the premise combined practise-experience and theoretical knowledges. Compare with the last wheels, the Ultra-big Dished Grinding-wheels No.3 pocess the characteristics of Anti-decyclization, excellent capability for super-speed grinding, great wearable capability etc.

The Moving Of Grinding Wheel

2016年7月9日星期六

Production Processing Of Grinding Wheel

The Balance Of The Grinding Wheel

Wheel knowledge




A wheel attribute categories



      
There are two characteristics determine the type of grinding wheel:



 
1.
From the material is divided, namely products used abrasive. Abrasive wheel determines the performance of different abrasive, apply the best wheel
Range has changed. Specific points, abrasives are the following: corundum abrasives, abrasive corundum, chromium corundum abrasives, single
Abrasive grain corundum, black corundum abrasives, abrasive silicon carbide green and black silicon carbide abrasive, micro-porosity wheel, grinding wheel small pores, atmosphere
Hole wheel, grinding wheel shoes, grinding wheel timber, paper mill wheel, grinding wheel, and other cloth.




2.
From the shape of the distinction between appearance of the style that is the product. The final shape of the finished abrasive wheel is different, the name is different.
Of course, the purpose is quite different. Preliminary points, mainly flat grinding wheel (circle, which both sides of the plane) and shaped sand
Round (irregular wheel) two categories. In actual use, flat grinding wheel in a dominant position, and its wide fan-shaped grinding wheel
More than made up for the shortcomings of flat wheel. Double-bevel wheel, single-bevel wheel, protruding wheel-sided, single-sided concave grinding wheel,
Sided concave grinding wheel, sheet wheel, cylindrical grinding wheel, cup grinding wheel, bowl-shaped grinding wheel, dish wheel, cylindrical grinding, round grinding cone
Head, spherical grinding head, Whetstone square, rectangular stone and so on.


Second, the hardness of the wheel selection and use



     


Wheel hardness
: The Wheel hardness selection and use of, for example, during normal use, the grinding wheel hardness refers to the wheel table
Sand surface during grinding off the degree of difficulty,
That is the extent of grinding wheel bond firmly bonded sand.
If the grinding wheel hardness
Is low, easy to fall off the sand, whereas the hardness of the wheel will be high, not falling. In order to meet the requirements of different grinding, you need to
There are various grades of hardness wheel wheel selection, in order to meet the needs of actual use, of abrasive hardness level according to
GB2484

2016年7月7日星期四

Dressing tools for shaping the dresser or repair to blunt the skin to restore face grinding performance during operation and the correct geometry. Timely and correct wheel dressing, is to improve the grinding efficiency and grinding quality assurance indispensable link. Dresser generally turning with a diamond wheel, grinding, rolling and other methods.

    
Turning trimming method in a single diamond particles (or finely made of diamond diamond diamond pen repair piece) as tool turning wheel is the most common method of trimming. Diamond tool mounted on the tool holder usually each inclined in both vertical and horizontal directions of about 5 ° ~ 15 °; the point of contact with the diamond wheel grinding wheel axis should be less than 0.5 ~ 2mm, trimming the diamond and make a uniform speed feed mobile. Surface roughness after grinding requires smaller, the feed rate should be lower, such as to reach the surface roughness Ra0.16 ~ 0.04μm, finishing feed rate should be less than 50mm / min. Trimming the total is generally sided 0.1mm around, back and forth several times dressing. Tinker cutting depth each of 0.01 ~ 0.03mm, refinement is less than 0.01mm. Diamond wheel trimming method using electroplating or powder metallurgy methods such as the large number of diamond particles embedded in the surface of the roller made of steel diamond wheel to a certain speed of rotation (thereby reducing the relative speed of the roller and the wheel), high-speed rotating grinding wheel surface cutting and rolling action, the grinding wheel and the roller profile to get consistent sharp work surface. Diamond wheel manufacturing complexity, high cost, but durable, high dressing efficiency, suitable for dressing grinding special shaping surface (such as threads, gears and turbine blade tenon tooth, etc.) wheel in mass production. Grinding wheel dressing method using super-hard silicon carbide grinding wheel rotating at high speed and low speed of rotation of the grinding wheel, in order to achieve the purpose of dressing. Rolling trimming method with carbide disc, a suit made of hardened steel wavy white iron discs or grooved from the wheel, and the wheel to roll and squeeze trimmed. Trim wheel typically mounted on the fixture manually, finishing high efficiency, suitable for coarse grinding wheel dressing.

Grinding Wheel In Glass Polishing


  Grinding is an important aspect, far from the fifties and sixties of optical glass processing is mainly carried out using grinding production on a large number, nearly a decade due to the development of building materials industry and light industry, rounded glass processing, chamfering hypotenuse processing (mainly for mirror industry, the country has hundreds of plant system and several diamond grinder to grind glass edges hundreds) also spent a lot of diamond grinding wheel for processing. another special grinding to EDM and abrasive composite processing, such as one of the products recently introduced machine tool plant is hole grinder to make copper electrode grinding of various hardness of metal holes.




Laser Marking Machine For lasing Grinding Wheel

ANCA gives: 7 Hot tips to acclerate your carbide tool production

Tip 1: The wheel is the world’s greatest invention, make it work overtime for you
Tip 2: Get your coolant clean and mean
Tip 3: Give your tools the support they need
Tip 4: Invest minutes in optimization to save hours in production
Tip 5: Deploy your anchor to avoid drift
Tip 6: Turn off the lights to save the planet
Tip 7: Rinse and repeat
Ceramic diamond grinding wheel, resin diamond grinding wheel, diamond grinding wheel metal | Juchuang Abrasive Co.,Ltd.

2016年7月6日星期三

Various problems should be noted during replacement of grinding wheel


Wearing problems:
Any Grinding wheel has its requirements for the use of certain wear, wear reaches a certain level must be re-replacement of the grinding wheel. Not in order to save material, it requires the use of ultra-wear, which is a very unsafe violations. A general rule, when the wheel wear to diameter ratio of diameter 10mm chuck should be replaced with a new wheel.

Validity of the problem:
The new wheel from the Treasury brought out is not necessarily qualified wheel, new wheel even buy from the manufacturers are not necessarily qualified wheel. Any wheel has its certain expiration date, under the terms of use, which is qualified grindstone; use over the period, it is not necessarily qualified wheel. Rules of "the use of the wheel should be within the validity period, resin and rubber bonded grinding wheel storage must be approved by turning test, those who pass before after one year."

Texture problem:
During use, if you find a local wheel cracks, stop using it immediately, replace the new wheel, wheel to avoid crushing injury accident.

 About the choice of diamond wheel diamond size, concentration, etc.
A diamond grinding wheel series: synthetic diamond, also known as "industrial diamonds", which, natural diamond, as it is known today is the hardest substance in nature. Because of its extreme hardness, compressive strength and wear resistance, acid and alkali as well as good thermal conductivity and semiconductor properties, so that it is made of a variety of tools products can be widely used in metallurgy, machinery, geology, petroleum , electronics, optics, construction, stone and other fields. Synthetic diamond grinding wheel is the main raw material of synthetic diamond powder with other metals at high temperatures, high pressure forming an artificial diamond products, and can be widely used in cemented carbide, ferrous metals and non-metallic grinding.
Two synthetic diamond grit size selected to represent the thickness of grit. Thickness directly affects the size of the surface roughness, and abrasive grinding efficiency loss. Choose granularity principle is to meet the requirements of the workpiece under conditions Use as large size, this can improve the grinding efficiency and reduce the loss of abrasive, diamond grinding step size it normally selected coarse particle size of grinding 30 # -120 # 120 # -240 # fine grinding mill 240 # -W40 grinding, polishing W40-W1
Three binders selected synthetic diamond grinding wheel according to different binding agents are generally divided into resin wheel, metal grinding wheel, electroplated grinding wheel and pottery wheel. Different binding agents have different properties, depending on the object to be processed to be required to choose the appropriate binder. No. The main purpose of binding agent on behalf of the resin binder B for carbide, glass, ceramics, stone and gem cutting, grinding. Metal binding agent M for carbide, glass, ceramics, stone, and other precious stones burden Heqie cutting, grinding, good wear resistance. Vitrified V for a variety of steel and cast iron dry and wet grinding, grinding is more suitable for the long axis and silk Hin. Plating binding agent D for a variety of special type of material surface grinding holes and valuable material cutting stock. Four selected concentration refers to the concentration of synthetic diamond content in the abrasive layer. ① resin bonded grinding wheel generally use 50% to 100% concentration; most of them with 75% finish high requirements can be less than 75%, profile grinding wheel and requires a long life, it can be 100% or more . ② metal bonded products generally used in concentrations of 25% to 150%; wherein the cutting blade coarse-grained, generally more concentration at the end, that is 25-50% fine-grained high; and other metal-bonded grinding wheels generally require concentration 50% to 100% concentration to. Overall, with a higher concentration of coarse grinding, semi-fine grinding with a medium concentration,

Laser Marking Machine For lasing Grinding Wheel

Grinding Wheel - Abrasive and size

(1) Abrasive
   The abrasive is the most important indicator wheel, grinding wheel thing is to rely on it, it does not mean there is no wheel this product. Abrasive selection requirements are more stringent, the grinding wheel and the workpiece when the friction is ultra-high temperature, high-temperature abrasive can not stand it, will soon melt away, so it is necessary to heat up; a lot of products are grinding metal and the like, and some are very hard, and abrasive hardness is not high, is the anti-grinding wheel hardness is relatively high; the time between the grinding wheel and workpiece are not instantaneous take some time, so it requires it has a strong toughness down. From the above several characteristics may probably know what will be the choice of the abrasive: diamond, corundum class, silicon nitride, etc., these are the world's most hard materials several, they have a strong wear resistance, high temperature resistance, toughness and appropriate. After different binding agents and manufacturing technology to produce a wide variety of wheel.

(2) particle size
  Abrasive particle sizes called granularity. Particle size into coarse-grained and fine-grained, grain size classification commonly used screening method, for example, the particles can pass through the sieve apertures 60 petit particles, that is fine-grained, can pass through the apertures 40 mesh, called large particles, that is, the coarse-grained. Sometimes sub-medium-grained, and some called powder. Wheel size to produce surface finish and processing efficiency of grinding workpiece significant impact, abrasive coarse grinding capacity, grinding efficiency is high, but the surface is rough, not so smooth; abrasive fine grinding is more uniform, the surface is relatively smooth processing ,, but cutting the amount is not so big, so relatively low grinding efficiency. It can be considered from the workpiece surface finish and grinding work efficiency of their choice.

2016年7月5日星期二

Dimensional roll feeder Production abrasive grinding wheel

Overview, classification, properties brief Of Grinding Wheel

Wheel profile:
Grinding wheel is the most important for a class of abrasive.
Abrasive wheel is added to the binding agent, a porous body through compacts made of dried and calcined. Due to the abrasive, bond and different manufacturing processes, a large difference in characteristics of the wheel, so the grinding process quality, productivity and economy have an important impact.
Wheel Category:
The press can be divided into ordinary abrasive abrasive (corundum and silicon carbide) abrasive grinding wheel and the natural and super abrasive grinding wheels (diamond and cubic boron nitride);
According to the shape can be divided into flat-shaped grinding wheel, bevel wheel, cylindrical grinding wheel, cup wheel, disc wheel and so on; press binding agent can be divided into ceramic wheel, resin wheel, rubber wheel, metal grinding wheel.
Wheel attributes:
Abrasive wheel is the central and the binding agent made of a circular abrasive through hole.
Characteristics of the grinding wheel abrasive, grain size, hardness, binding agents, shape and size and other factors to determine.
Knowledge of grinding wheel

Font size: large and small 16:10 2014-03-26 reading (23) review (0) classification:

Round consolidated abrasive tools made of abrasive and binding agent, etc.. The grinding wheel is abrasives used most widely, the largest use a, using high-speed rotation, of metal and nonmetal workpiece excircle and inner circle, plane and various type surface of roughing, semi finishing grinding and fine grinding and notching and cutting. A wide variety of grinding wheel. By the use of abrasive can be divided into ordinary abrasive wheel (corundum and silicon carbide, etc.) and super hard abrasive (diamond and cubic boron nitride grinding wheel; shape can be divided according to flat shaped wheel, bevel wheel, wheel cylinder, cup wheel, disc wheel, etc., according to the bond can be divided into ceramic grinding wheel, resin grinding wheel, rubber wheel, grinding wheel, metal. The characteristic parameters of the grinding wheel mainly include abrasive, viscosity, hardness, bond, shape, size and so on. Since the grinding wheel usually work at high speed, it should be carried out before the use of rotary test (to ensure that the grinding wheel at the maximum operating speed, not broken) and static balance test (to prevent the work caused by machine vibration). After working for a period of time, the grinding wheel should be trimmed to restore the grinding performance and the correct geometry.

The use of grinding wheel has a certain risk. For everyone's safety, the use of the following note:

Grinding wheel machine is one of the most commonly used machine equipment in the machinery factory. Its installation is reasonable, whether it meets the safety requirements; its use method is correct, whether it is in compliance with the safe operating procedures. These problems are directly related to the personal safety of every employee, so we must pay more attention to the actual use.

1 matters needing attention in installation process

Positioning of the problem of sand turbine installation in what position, is the process of installation, we must first consider the problem, only selected a reasonable and appropriate location, the grinding wheel can do other work. Grinding wheel machine is not installed in the vicinity of the equipment and operating personnel or frequently in the past, the general larger workshop should set up a special grinding wheel machine room. If you do not set the special grinding wheel machine room due to the limitation of the terrain, it should be installed on the front of the sand turbine not less than 1.8m height of the protective baffle, and the baffle board is required to be firm and effective.

The imbalance of the grinding wheel is mainly caused by the manufacture and installation of the grinding wheel, and the center of gravity of the grinding wheel is not coincident with the rotating shaft. The harm caused by the imbalance is mainly manifested in two aspects, on the one hand in wheel rotates at a high speed, causing them to vibrate, easy cause workpiece surface to produce a polygonal oscillation mark; on the other hand, the imbalance in accelerated the vibration of the shaft and bearing wear, serious will cause the wheel broken, and even cause accidents. Therefore, straight much greater than or equal to 200mm sand office floor mounted on the chuck should first static balance, grinding wheel after truing or at work found that imbalance should be repeated static balance.

The problem of matching mainly refers to the problem of the grinding wheel chuck and supporting the installation of. In accordance with the standard requirements, the grinding wheel chuck diameter shall not be less than is installed 1 / 3 of the diameter of the office building of the sand and corresponding provisions of grinding wheel wear to diameter ratio chuck diameter of 10 mm should be replaced with new grinding wheel. So that there is a matching problem of a chuck and a grinding wheel, otherwise it will appear such circumstance, "big horse drawn cart cause a waste of equipment and materials;" small horse drawn carts "and does not meet the safety requirements, easy to create adults accident. Therefore, reasonable match of the chuck and the grinding wheel, on the one hand can save equipment, cheyo materials; on the other hand and in conformity with the safety requirements. In addition, between the grinding wheel and the chuck also should be equipped with chuck diameter greater than the diameter 2mm, thickness of 1mm~2mm cushion.

Protection shield is sand turbine the main protection device, its role is: grinding wheel piece when grinding wheel at work for some reason failure to effectively covering the wheel fragments, ensure personnel safety. The shape of the protective cover of the grinding wheel is round and square two, and the maximum opening angle of the grinding wheel is not allowed to exceed 90 degrees; the material of the protective cover is not less than 415N/mm2 steel. When the new grinding wheel is changed, the installation of the protective cover is firm and reliable, and the protective cover is not allowed to disassemble or discard at will.

Block Qiao panel is grinder main door accessories of protective cover in above the horizontal spindle surface opening is greater than or equal to 30 (must be set up for this device. Its main function is to block in the process of grinding fly quietly so as not to hurt the operator. It is installed at the opening end of the protective cover, the width should be larger than the width of the wheel guard, and should be fixed firmly on the protective cover. In addition, the gap between the surface of the grinding wheel and the baffle plate should be less than 6mm.

The bracket is one of the accessories used in the sand wheel machine, and the grinding wheel diameter is more than 150mm. The distance between the grinding wheel and the bracket should be less than 1/2, but the maximum should not exceed 3mm.

The ground problem is to use the power line, so the shell of the equipment must have a good grounding protection device. It is also one of the important factors to cause accidents.

2 matters needing attention in the use of the process

Side grinding problems in the daily use of grinder, we often can freely use the side of the grinding wheel for grinding, some operators is not divided into types of grinder, grinding wheel are found. This is a serious violation of the rules for safe operation of the illegal operation behavior. According to the rules of the surface to do the work surface of the grinding wheel is not suitable to use the side of the grinding, the radial strength of the grinding wheel

Strength of Defined Wheel



Abrasives include tensile strength, flexural strength, compressive strength and resistance to funk.
N is the maximum strength under tensile stress tensile performance abrasive, it is abrasive manufacturing, use a secondary index on direct and abrasive is being high speed winding can rupture strength.
Flexural strength performance abrasive maximum allowable bending stress or bending limit. In abrasive grinding for molding, such as thread grinding, crankshaft grinding and all kinds of plunge grinding, etc., are required to wear is being kept good flexural strength, to resist bending stress grinding attack.
Compressive strength abrasive performance is being under pressure abrasive strength limit, such as n-abrasive wheel is being increased radial load grinding blunt breakage and cracking can occur on the extent of the compressive strength.
Anti-abrasive performance abrasive funk strength is being fixed RESISTANCE funk force under load.
Abrasives abrasive strength from the manufacturing process, coupling agents and abrasive performance specifications, abrasive strength of the factors are: abrasive type, size, variety and performance of the coupling agent, abrasive position with the organization, density, mixing and heat treatment process conditions, abrasive shape, and the aperture ratio of the outer diameter of the wheel. Process is being abrasive characteristics and specifications given current, the coupling agent performance and heat treatment conditions on the most minor.


http://www.jcabrasive.com

2016年7月4日星期一

Brief introductionCentral abrasive and a binder resin made of a circular abrasive through hole. Abrasive wheel is the most widely used as a maximum amount, the use of face, high-speed rotation, can the outer, inner circle, plane type and various other metal or non-metal surface of the workpiece when using coarse grinding, fine grinding and half grooving and grinding and cutting and so on. Wheel variety. The press can be divided into ordinary abrasive abrasive (corundum and silicon carbide) abrasive grinding wheel and the natural and super abrasive (diamond and cubic boron nitride) grinding wheel; according to the shape can be divided into flat-shaped grinding wheel, bevel wheel, cylindrical grinding wheel, cup wheel, disc wheel and so on; press binding agent can be divided into ceramic wheel, resin wheel, rubber wheel, metal grinding wheel. The main parameters of the abrasive wheel, viscosity, hardness, binding agents, shape, size and so on. Since the wheel typically operate at high speed, before turning test should be carried out so that the use of (guaranteed wheel at the maximum operating speed, do not break) and static balance test (when working to prevent vibrations caused by the machine). Grindstone at work for some time, it should be trimmed in order to restore the grinding performance and the correct geometry.PrecautionsWheel using a certain degree of risk. For everyone's safety, are listed below using precautions:Grinder is one of the most commonly used mechanical plant equipment, its installation is reasonable, whether compliance with safety requirements; the use of it is correct, whether compliance with safety rules. These problems are directly related to the safety of every employee, so in actual use must draw our attention.
1 installation process Precautions
First of all to secure the quality of the grinding wheel while installing the detection method, the Nepalese velvet hammer (can also be pen) tapping the side of the wheel, the sound is crisp, no problem.Orientation grinder installed in any position, is the question we must first consider the installation process, only the selected reasonable and suitable location, we can carry out other tasks. Grinder prohibit installed facing or near the equipment and operating personnel often been in the past where, generally larger workshop should set up a dedicated wheel room. If indeed due to terrain limitations plant can not set up a dedicated wheel room, shall be installed in the front of the wheel height of not less than 1.8m protective bumpers and bumpers require a solid and effective.Unbalanced balance wheel mainly by the grinding wheel manufacture and installation of inaccurate center of gravity so that the wheel does not coincide with the rotary shaft caused. Harm imbalance mainly manifested in two aspects, one at the wheel rotating at high speed, causing the vibration, could easily lead to the workpiece surface polygonal oscillation marks; on the other hand, accelerated the unbalance vibration of the spindle and bearing wear, serious when the wheel will cause rupture and even cause accidents. Therefore, requires a lot greater than or equal straight fitted chucks should be static balance wheel during trimming after shaping or imbalance found in the work, it should be repeated static balance 200mm sand office.Matching matching problem mainly refers to the chuck and the wheel mounting support issues. According to standards, not less than the diameter of the wheel chuck is mounted sand office diameter of 1/3, and the corresponding provisions of wheel wear to a diameter of 10mm diameter larger than the chuck should be replaced with a new wheel. This presents a problem matching the chuck and the grinding wheel, otherwise there will be such a situation, the "big horse car" wasteful equipment and materials; "small horse cart" do not meet the safety requirements, could easily lead to accidents. Therefore, a reasonable match with the chuck wheel, on the one hand can save the device, cut about material; on the other hand meet the requirements for safe operation. Further, between the grinding wheel and chuck chuck should install a larger diameter than the diameter of 2mm, 1mm ~ 2mm thick cushion.Protective shield problem is the main grinding machine guards, whose role is: When the wheel for some reason undermine the job, effectively covering the wheel debris, to ensure the safety of personnel. Wheel shape shield round and square, its maximum opening angle must not exceed 90 °; shield material is not less than the tensile strength of 415N / mm2 steel. When replacing a new wheel, shield installation should be solid and reliable, and the guards can not be demolished or do not discard.Quiet block panel is one of the main protective accessory grinder, shield above the level of the main shaft opening is greater than or equal to 30 must reset this device (when. Its main function is to block the grinding process flying quiet to avoid harming operator. it is attached to the positive terminal of the protective hood opening, the width should be greater than the width of the wheel guard, and should be firmly secured in a protective cover. in addition, the surface of the wheel peripheral clearance requirements baffles should be less than 6mm.Bracket bracket problem is one of the commonly used grinder attachment, according to the provisions wheel diameter of 150mm or more grinders must be set adjustable bracket. The distance between the wheel and the bracket should be less than the workpiece to be ground to make the smallest form factor of 1/2 inch, but the maximum should not exceed 3mm.Grounding grinder using power lines, and therefore housing of the device must have a good grounding protection device. This is easily one of the important factors in the accident.
2 Precautions during use
Side grinding problem in everyday use grinders, we often can find some operator, regardless of the type of grinding machines, regardless of the type of wheel, optionally grinding wheel on the use of the side, which is a serious breach of security operations operating procedures illegal behavior. Procedures used by the circumferential surface of the face do not use the side wheel for grinding large radial strength of this wheel, axial strength is small, it will cause the wheel broken, even wounding the operator the force is too large, the actual the use of the process should prohibit such behavior.Positive operational problems in everyday use, many operators always used to facing the grinding wheel to operate, because this direction can pull its weight, in fact, this behavior is a grinder operating behavior should be particularly prohibited. Follow the rules, the use of grinders grind the workpiece, the operator should stand on the side of the wheel, the front wheel must not operate so as not to fail the wheel, or the wheel broken wheel fly flying wounding.Operational problems in the use of force grinder, some operators, especially the younger operators, for the sake of grinding speed, force too much too fast, this is a very unsafe practices. Any wheel body has a certain level of strength, doing so is likely to cause a broken wheel, and even flying out of wounding, but also a should be prohibited.Common operational problems in the actual daily operation, but also this happens, someone to catch production tasks, grab working hours, the two share a grinder while operating, which is a serious violation of operating behavior should be strictly prohibited. A grinder is not enough time, you can add grinder solution, and definitely not at the same time share a grinder.
3 replacement process Notes
Any wheel wear problems it has certain requirements for the use of wear, the wear reaches a certain level must be re-replacement of the grinding wheel. Not in order to save material, it requires the use of ultra-wear, which is a very unsafe violations. A general rule, when the wheel wear to diameter ratio of diameter 10mm chuck should be replaced with a new wheel.Validity of the problem from the Treasury brought a new wheel is not necessarily qualified wheel, new wheel even buy from the manufacturers are not necessarily qualified wheel. Any wheel has its certain expiration date, under the terms of use, which is qualified grindstone; use over the period, it is not necessarily qualified wheel. Rules of "the use of the wheel should be within the validity period, resin and rubber bonded grinding wheel storage must be approved by turning test, those who pass before after one year."Texture problems in the course, if you find a local wheel cracks, stop using it immediately, replace the new wheel, wheel to avoid crushing injury accident.
4 Other considerations should
Environmental issues in general should set up a dedicated grinder wheel room, and the room is strictly prohibited in the vicinity of the wheel grinder or stacking flammable items, to avoid fire or explosion, or other components should not be misplacing objects in the vicinity of the grinder.Management grinder should be the person responsible for this non-unit personnel who want the grinder when grinding on the object, subject to full-time person in charge of licensing and compliance with safety procedures strictly prohibited without the consent of the responsible officer, the indiscriminate use of unauthorized outsiders grinder. In addition, the replacement of the grinding wheel is also the person responsible should prevent others from unauthorized replacement, install the wheel.Off the problem of car operator stops working, you should immediately turn off the car. Prohibition grinder idle in the absence of use, unattended situation. Furthermore, it should be kept clean after use shortwave turbine.ScheduleAbrasive wheel is the central and the binding agent made of a circular abrasive through hole.Determined by properties of the abrasive grinding wheel, grain size, hardness, binding agents, shape and size and other factors, we are presented below, respectively.(1) abrasives and abrasive selection is the main raw material to manufacture grinding wheel, which bears the cutting work. Thus, the abrasive must be sharp and have high hardness, good heat resistance and a certain toughness. The name commonly used abrasive, code, characteristics and uses are shown in Table 1.Table 1 Common abrasivesCategory names Use Code features oxide corundum A (GZ) containing 91 to 96% alumina. Brown, high hardness, good toughness, cheap grinding carbon steel, alloy steel, malleable iron and hard bronze corundum WA (GB) containing 97 to 99% alumina. White, higher than the corundum hardness, low toughness, good self-sharpening, grinding less heat when grinding hardened steel, high carbon steel, high-speed steel and carbide black silicon carbide thin-walled parts C (TH) containing more than 95% silicon carbide. Black or dark blue, shiny. Higher hardness than corundum, brittle and sharp, good thermal and electrical conductivity of grinding cast iron. Brass, aluminum, refractory materials and non-metallic materials green silicon carbide GC (TL) containing more than 97% of silicon carbide. Green, hardness and brittleness higher than TH, thermal and electrical conductivity, good grinding carbide, optical glass, precious stones, jade, ceramic, honing engine cylinder liner wear high hardnessDepartment of synthetic diamond material D (JR) colorless or light yellow, yellow-green, black. High hardness, brittle than natural diamond properties. The price is better than other abrasive grinding times more expensive carbide gemstones high hardness materials cubic boron nitride CBN(JLD) cubic crystal structure, slightly lower than the hardness of diamond, high strength, good thermal conductivity grinding, grinding, honing a variety of hard and tough hardened steels and high molybdenum, high alumina, high cobalt steel, stainless steelNote: The code in brackets are the old standard code.(2) Select the size and granularity refers to the size of the abrasive granule. Grit and powder particle size groups. Abrasive Grain screening classification, which mesh aperture medium grain size number to one inch over the length of the number to represent. E.g., abrasive grit # 60, by instructions per inch mesh has perforations 60, and not through the perforations 70 per inch sieve. The classified powder by microscopic measurement, its actual size abrasive grit to be represented (W). Various grit grit size shown in Table 2.Table 2 and a particle size of the abrasive gritAbrasive grit abrasive powder particle size (um) grit particle size (um) grit particle size (um) 14 # 1600 ~ 1250 70 # 250 ~ 200 W40 40 ~ 28 16 # 1250 ~ 1000 80 # 200 ~ 160 W28 28 ~ 20 20 # 1000 ~ 800 100 # 160 ~ 125 W20 20 ~ 14 24 # 800 ~ 630 120 # 125 ~ 100 W14 14 ~ 10 30 # 630 ~ 500 150 # 100 ~ 80 W10 10 ~ 7 36 # 500 ~ 400 180 # 80 ~ 63 W7 7 ~ 5 46 # 400 ~ 315 240 # 63 ~ 50 W5 5 ~ 3.5 60 # 315 ~ 250 280 # 50 ~ 40 W3.5 3.5 ~ 2.5Note: more than 14 # coarse grains and fine powder finer than W3.5 rarely used, it is not listed in the table.Grit size selection, mainly with surface roughness and productivity related.When rough grinding to a large margin, the required surface roughness is large, coarse grains should be used. Because coarse grains, large pores, grinding depth can be larger wheel clogging and fever. When grinding, the balance is small, requiring a lower roughness values, you can select finer grit. In general, the more fine abrasive grinding surface roughness better.Different size wheel applications are shown in Table 3.Table 3 different wheel size rangeWheel size wheel size range generally used generally range 14 ~ # 24 # mill steel ingot, billet cutting, grinding and casting burrs 120 # ~ W20 grinding, honing and thread grinding 36 # 60 # general grinding plane, cylindrical, inner circle and centerless grinding W20 or less mirror grinding, honing fine 60 # to 100 # grinding and tool sharpening, etc.(3) binding agents and their selection for bonded abrasive grinding wheel substance called binder. Wheel strength, impact resistance, heat resistance and corrosion resistance is mainly determined by the performance of a binding agent. Commonly used types of binding agents, properties and uses are shown in Table 4.Table 4 Common binding agentName code performance Use vitrified V (A) water, oil, acid, alkali corrosion, to maintain the correct geometry. Porosity and a large grinding rate, greater strength, toughness, flexibility, vibration resistance is poor, can not withstand lateral forces V wheel <35m / s grinding, this binding agent most widely used, can be made into a variety of mill tools for form grinding and thread grinding, gear, crankshaft and other resin binder B (S) strength and elastic, not afraid of the impact, can work at high speed. Friction polishing action, but strong resistance and heat resistance than the ceramic binder is poor, not acid, alkali, porosity is small, easy to plug the V round of> 50m / s high-speed grinding, grinding wheel can be made thin groove, sharpening the tool rake face. Precision grinding. When wet milling cutting fluid alkali content should be <1.5% binding agent rubber R (X) greater elasticity than the difference between the binder resin, strength is also large. Porosity is small, easy to fall off abrasive, poor heat resistance, not oil, not acid, but also the smell of manufacturing grinding wheel bearing channel and centerless grinding wheel, guide wheel and a variety of slot and sheet cutting grinding wheel, polishing wheel made of soft metal such as binding agents(Bronze, nickel plating) J toughness, formability, strength, self-sharpening poor performance of manufacturing all kinds of diamond abrasive, long lifeNote: The code in brackets are the old standard code.(4) Select the wheel hardness and hardness is the degree of difficulty on the abrasive grinding wheel surface under the force of falling. Wheel hardness soft, showing grit wheel off easily, the hardness of the wheel hard, abrasive grains showing off more difficult. Abrasive grinding wheel hardness and hardness are two different concepts. With an abrasive wheel may be made of different hardness, which is mainly determined by the binding agent performance, as well as the number of wheel manufacturing processes. Significant differences between the grinding wheel and the cutting is "self-sharpening", select the hardness of the wheel, in fact, is to choose self-sharpening wheel, hoping to further sharp abrasive grains do not fall off too early, and do not fall off not blunt the .According to regulations, common wheel hardness level in Table 5.Table 5 Common Wheel hardness levelHardnessGrade Large stage soft soft hard hard in the small stage soft 1 soft 2 Soft 3 soft 1 soft 2 1 2 1 Hard 2 Hard Hard Hard 1 Hard 2 Generation 3 No. G(R 1) H(R 2) J(R 3) K(ZR 1) L(ZR 2) M(Z 1) N(Z 2) P(ZY 1) Q(ZY 2) R(ZY 3) S(Y 1) T(Y 2)Note: The code in brackets are the old standard code; ultra-soft, hard not included; Tables 1, 2, and 3 in order of increasing hardness.Selection of grinding wheel hardness general principle is: the processing of soft metals, in order not to make premature loss of abrasive, then use a hard wheel. When machining hard metal, in order to make timely blunt abrasive grains fall off, thereby exposing new abrasive grains with sharp edges (ie, self-sharpening), use soft grinding wheel. The former is because the soft material grinding wheel abrasive wear is very slow work, without departing too early; the latter because when grinding hard materials, abrasive wear wheel work faster, you need fast update.When grinding, grinding in order to ensure the accuracy and roughness, should be used slightly harder wheel. Poor thermal conductivity of the workpiece material, burns and easy to produce cracks (such as grinding carbide, etc.), use the wheel to be softer.(5) the shape and size of the machine structure and select the desired grinding wheel made of various shapes and sizes. Table 6 are several kinds of wheel shape, size, and application code.The outer diameter of the wheel should be as the election was bigger, in order to improve the peripheral speed of the wheel, so to improve productivity and grinding surface roughness favorable. In addition, under conditions of the machine rigidity and power permit, such as the selection of the width of the larger wheel, you can also receive increase productivity and reduce the effect of roughness, but high grinding heat-sensitive materials in order to avoid burns and the workpiece surface cracks, wheel width should be appropriately reduced.Table 6 Common wheel shape and purposeWheel size code name schematic representation of the main purposes flat-shaped grinding wheelP P D × H × d for cylindrical grinding inner circle, plane and centerless grinding wheel biconcavePSA PSAD × H × d-2-d 1 × t 1 × t 2 for cylindrical grinding, centerless grinding and sharpening knives double bevel wheelPSX PSX D × H × d for grinding gears and threaded cylindrical grinding wheelN N D × H × d for vertical flat end mill sand wheel discD D D × H × d for sharpening knives in front of a bowl-shaped grinding wheelBW BW D × H × d for rail grinding and grinding toolsFor example, the meaning of numbers41-A30Q4BF MAX SPEED R.P.M41According to international practice refers T41- parallel grinding wheel cutting wheel T27- T42- cymbals cymbals grinding wheelAAbrasive: A- C- BC corundum WA- corundum silicon carbide GC GreenAC SA- mixing abrasive corundum crystal BA- MA- microcrystalline corundum corundum black corundum ZA-PA- chrome corundum corundum SG- FA- half brittle ceramic corundum SC- cubic boron carbide BC- Diamond D-30Abrasive particle size: min 16, 20, 24, 30, 36, 40, 46, 54, 60, 70, 80, 90, 100, 120, 150, 180, 220.240 (referred to as a fine powder)QWheel hardness scale: F, Q, H, J, K, L, M, N, P, Q, R, S, T, Y4Organization number: abrasive grinding wheel according to product volume ratio of share points0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12BBinding agent typeFEnhancedMAX SPEEDMaximum permissible line speed m / sR.P.MThe maximum permissible speed r / min

Overview, classification, properties brief Of Grinding Wheel


Wheel profile:
Grinding wheel is the most important for a class of abrasive.
Abrasive wheel is added to the binding agent, a porous body through compacts made of dried and calcined. Due to the abrasive, bond and different manufacturing processes, a large difference in characteristics of the wheel, so the grinding process quality, productivity and economy have an important impact.
Wheel Category:
The press can be divided into ordinary abrasive abrasive (corundum and silicon carbide) abrasive grinding wheel and the natural and super abrasive grinding wheels (diamond and cubic boron nitride);
According to the shape can be divided into flat-shaped grinding wheel, bevel wheel, cylindrical grinding wheel, cup wheel, disc wheel and so on; press binding agent can be divided into ceramic wheel, resin wheel, rubber wheel, metal grinding wheel.
Wheel attributes:
Abrasive wheel is the central and the binding agent made of a circular abrasive through hole.
Characteristics of the grinding wheel abrasive, grain size, hardness, binding agents, shape and size and other factors to determine.


2016年7月1日星期五

Identification and Selection Of Grinding Wheel

Identification and Selection Of Grinding Wheel
      The hardness of the wheel represents the soft abrasive wheel off easily, abrasive grinding wheel hardness should mean more difficult to fall off. Wheel hardness and hardness of the abrasive is two totally different concepts, with an abrasive wheel may be made of different hardness, it depends on the performance, the number of manufacturing processes and wheel binding agent.

      Grinding wheel and the cutting has a significant difference, choose the hardness of the wheel is actually choose from Yue of the wheel, hoping sharp abrasive grains do not fall off too early, and do not blunt the not fall off.
The shape and size of main wheel according to the conditions and the workpiece shape, material properties and other factors to select the grinder. General still need to be selected after the appearance of the wheel and crack identification, but sometimes difficult to observe internal crack in the wheel, then use the sound test, such as tapping with a mallet to listen to the sound, the sound was not clear pickled good crack wheel .
      As for the selection of the wheel will have to consider when considering the size, as far as possible to the outer diameter of the general election was bigger; vertical mill should be a wide choice of wheel; when the mill circle, take the outer diameter of the workpiece aperture wheel 2 / 3.
      In addition, it should be noted that in particular, the linear velocity of the grinding wheel used must not exceed the value of the flag.


http://www.jcabrasive.com